Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
We have encountered this article involving Installing A Bathtub down the page on the internet and reckoned it made good sense to talk about it with you on my blog.
Setting up a bathtub isn't precisely rocket science, however it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably difficult job. If the old tub is readily available, the task can relocate immediately; if you need to open a wall to remove the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and also set in the new one. See to it you have certified on your own for the work and also are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This post will certainly assist you set up a new tub in your shower room if you have already bought a new bathtub and also do not need to change the setup of your previous water supply pipelines.
Your devices and product list should consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any kind of water staying in the system. The process of eliminating the existing taps can be fairly bothersome as a result of the limited access that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in location between the tap and the sink. Secure the tap in place with the supplier given backnut. Once the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The previous kind must be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the tub until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost versatile faucet port to the proper supply pipe by making a compression join; then do the very same for the other tap.
Turn on the supply of water and examine all joints and brand-new pipework for leakages and tighten them if necessary. Fill up the bath tub as well as also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub ought to wait up until the bath tub has actually been utilized at least when as this will certainly settle it right into its final placement.
Getting ready for the Setup
Firstly, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, bring about difficulties with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in usage. The sealer can split fairly early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly available on the marketplace. It is recommended to fit the tiles using water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog posting about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when looking around the internet. For those who liked our article kindly remember to share it. Thanks a lot for your time. Visit again soon.
Book A Free Estimate Report this page